Ritron OUTPOST Series Informacje Techniczne Pobierz pdf (Strona 15)

OUTPOST Wireless Callbox PC Programming

PC P

ROGRAMMABLE

UTPOST

ALLBOX

™ F

EATURES

(

CONTINUED

)

Transmit Beep Enable

This feature is turned on from the factory to provide a

short beep in the Callbox speaker any time the

ON/PTT button is pressed. This assures the Callbox

user that the radio has turned on and is ready to

transmit their message. With this feature disabled the

Callbox will only beep when the radio is first turned on.

RX Courtesy Beep Enable

In high noise environments it is sometimes difficult to

determine when a received message has ended. With

the RX Courtesy Beep enabled the Callbox will sound

a short beep on the speaker at the end of each re-

ceived transmission.

Sensor Input

The Callbox will send a warning tone when a change

in the Sensor Input is detected. The Sensor Input will

respond to an OPEN or CLOSED switch.

Narrowband

The OUTPOST™ Callbox can be programmed to op-

erate wide or narrow band on any programmable fre-

quency within the specified range.

Companding

The radio can be programmed to enable or disable

audio companding. Companding will compress trans-

mit audio before sending it, and expand receive audio

before it is heard on the speaker to reduce the back-

ground noise common in radio communications.

High / Low Power

The Callbox can be set to transmit at high (2-Watt) or

low (1-Watt) power. Low power is recommended in

battery powered installations.

Refer to

Special Note on page 3 regarding Alkaline

battery use.

WITCH

UTPUT

PTIONS

–A

LLOWS

ONTROL OF AN

XTERNAL

EVICE

..............................................................................

The switch output is a simple 1-Amp relay contact clo-

sure that can be used to OPEN and CLOSE a gate,

switch on a light, sound an alarm or any other applica-

tion where remote control of an ON/OFF switch is re-

quired. The OUTPOST Callbox can be PC pro-

grammed to OPEN and CLOSE the Switch Output

when one of the following programmed conditions is

met.

The Callbox can be PC programmed to alternately

OPEN and CLOSE the switch using a single 2-tone

code, or can be PC programmed for separate OPEN

and CLOSE 2-tone codes. Field programming offers

nine 2-tone codes that correspond to field program-

mable 2-tone codes available in select RITRON port-

able and base radios.

No Switch

Select this option for no switch operation.

Switch On When Called

With this option selected the switch will CLOSE when

the Callbox first receives a call. The switch will remain

CLOSED until the ON/PTT button is pressed or the

RQX Reset Time expires. This option is not applicable

if the Callbox is programmed for Automatic Turn-Off.

Switch On When Callbox in Use

This option will CLOSE the switch when the Callbox

first sends or receives a call. The switch will remain

closed until the RQX Reset Time expires, which also

turns the radio off if it is programmed for Automatic

Turn-Off.

Switch On When Active with Turn-Off Code

This option operates the same as Switch On When

Callbox in Use with the added ability to OPEN the

switch when a unique 2-Tone Turn-Off Code is re-

ceived. Unlike the Switch On When Callbox in Use

feature, the switch will not OPEN when the RQX Re-

set Time expires unless the Callbox is programmed for

Automatic Turn-Off. See the 2-Tone Decode Setting

section on page 14 of this manual for details on pro-

gramming a 2-Tone Turn-Off code.

GateGuard™ – Momentary for 1 sec.

With this option selected the switch will momentarily

CLOSE when a unique 2-Tone code is received. The

switch will remain CLOSED for the programmed pe-

riod of time, programmable for 1-255 seconds. See

the 2-Tone Decode Setting section of this manual for

details on programming a 2-Tone code. Field pro-

gramming the Callbox for GateGuard™ operation

places the radio into this momentary mode.

GateGuard™ – Toggle

With this option selected the switch will alternately

OPEN and CLOSE when it receives a unique 2-Tone

code. After the 2-tone code is received the Callbox will

transmit a SINGLE BEEP if the switch has been

OPENED and a DOUBLE BEEP if the switch has

been CLOSED. The switch will open when the Callbox

turns off if it is programmed for Automatic Turn-Off.

See the 2-Tone Decode Setting section of this manual

for details on programming a 2-Tone code.

GateGuard™ – On Code / Off Code

When this option is selected the switch will CLOSE

when a unique 2-Tone code is received, and OPEN

when the 2-Tone Turn-Off code is received. The

switch will OPEN when the Callbox turns off if it is

programmed for Automatic Turn-Off. See the 2-Tone

Decode Setting section of this manual for details on

programming a 2-Tone code and a 2-Tone Turn-Off

code.

Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 13

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 21 22

Komentarze do niniejszej Instrukcji

Brak uwag

Ritron OUTPOST Series Informacje Techniczne Strona 15

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Radiotelefony Ritron OUTPOST Series